Differences of the effect of thermal treatment in an oxygen-containing gas medium on properties of the surface layer Ti, Zr, Hf

Надіслано: Вересень 12, 2019
Переглянуто: Листопад 14, 2019
Прийнято: Грудень 28, 2019
1
Фізико-механічний інституту ім. Г.В. Карпенка НАН України
2
Karpenko Physico-Mechanical Institute of the NAS of Ukraine
3
Karpenko Physico-Mechanical institute of the National Academy of Sciences of Ukraine
4
National Science Center «Kharkov Institute of Physics and Technology» of the National Academy of Sciences of Ukraine
5
National Science Center «Kharkov Institute of Physics and Technology» of the National Academy of Sciences of Ukraine
6
National Science Center «Kharkov Institute of Physics and Technology» of the National Academy of Sciences of Ukraine

The paper presents the characteristics of the surface layer of d-elements of the IV group (titanium, zirconium and hafnium) after thermal diffusion saturation from a controlled oxygen-containing gas medium. Saturation was carried out at = 750 °C for t = 5 hours at different pressures (P = 1.33∙10–1 Pa, = 1.33∙10–2 Pa, P = 1.33∙10–3 Pa). Experimentally revealed differences in the characteristics of the surface layer of titanium, zirconium and hafnium.

It was shown that a hardened diffuse layer is formed with a higher hardness relative to the metal core in the reverse order of their affinity for oxygen. On titanium, zirconium and hafnium, only a diffuse layer is formed without a phase film. The appearance of the surface of the samples before and after processing is given.

According to the results of the study, chemical-thermal treatment in an oxygen-containing gas medium leads to changes in the surface layer of sheet material from titanium, zirconium and hafnium. The state of the surface layers directly affects the characteristics of finished products, in particular, fatigue life. Therefore, this treatment is a good tool for controlling the state of the surface layers of the aforementioned metals, and then their properties.

[1] Titanium and Titanium Alloys: Fundamentals and Applications, C. Leyens, and M. Peters, Eds. Weinheim, Germany: WILEY-VCH Verlag GmbH & Co., 2003.

[2] V. N. Moiseyev, Titanium Alloys. Russian aircraft and aerospace applications. Boca Raton, Fl: CRC Press, 2005.

[3] C. Lemaignan, and A. T. Motta, “Zirconium Alloys in Nuclear Applications”, in Materials Science and Technology. New York: Wiley, 2013, pp. 1–51.

[4] R. T. Allsop, “Titanium, Zirconium and Hafnium”, in Chemistry of the Elements, N. N. Greenwood, and A. Earnshaw, Eds. Oxford, UK: Elsevier Butterworth-Heinemann, 1997, pp. 954–975.

[5] A. K. Shikov, O. V. Bocharov, V. M. Arzhakova, et al., “Use of Hafnium in Control Elements of Nuclear Reactors and Power Units”, Metal Science and Heat Treatment, vol. 45, pp. 300–303, 2003.

[6] L.-P. Lefebvre, E. Baril, and L. de Camaret, “The effect of oxygen, nitrogen and carbon on the microstructure and compression properties of titanium foams”, Journal of Materials Research, vol. 28, no. 17, pp. 2453–2460, 2013.

[7] S. Yamanaka, T. Tanaka, and M. Miyake, “Effect of oxygen on hydrogen solubility in zirconium”, Journal of Nuclear Materials, vol. 167, pp. 231−237, 1989.

[8] S. Yamanaka, Y. Fujita, M. Uno, and M. Katsura, “Influence of interstitial oxygen on hydrogen solubility in metals”, Journal of Alloys and Compounds, vol. 293−295, pp. 42−51, 1999.

V. Trush, V. Fedirko, A. Luk’yanenko, P. Stoev, M. Tikhonovsky, K. Kovtun, "Differences of the effect of thermal treatment in an oxygen-containing gas medium on properties of the surface layer Ti, Zr, Hf", Ukrainian Journal of Mechanical Engineering and Materials Science, vol. 5, no. 3-4, pp. 39-43, 2019.