CALIBRATION OF ANALYZERS OF THE MOBILE COMMUNICATION SYSTEM PARAMETERS

2022;
: pp. 30-34
1
State Enterprise “Ukrmetrteststandard”
2
Інститут електромагнітних вимірювань Державного підприємства «Укрметртестстандарт», Київ, Україна

The creation and operation of mobile communication systems is impossible without determining the parameters of base stations and mobile communication systems. For these purposes, appropriate devices are used that optimally combine testing capabilities in a single portable solution, which eliminates the need for several separate control and measuring devices. One of the main types of measurements of such devices is the measurement of the power of ultra-high and extremely high frequency signals. The article presents the method of calibrating meters of directional and absorbed power of ultra-high and extremely high frequency signals using the Bird 5000-EX mobile communication system parameter analyzers complete with the Power Sensor 5010V sensor and measuring sensors, Anritsu CellMaster MT8212EA and Arnitsu SiteMaster S331E spectrum analyzers. Calibration schemes for analyzers of parameters of mobile communication systems and analyzers of mobile communication base stations (hereinafter referred to as analyzers) have been developed. A measurement model of the analyzers based on the parameters of the directional and absorbed power of ultra-high and extremely high frequency signals based on the developed calibration schemes was created. The contribution of each component of the measurement model to the calibration result and the corresponding uncertainties of the model components were determined. The measurement uncertainty budget was made based on the proposed analyzer calibration model. The influence of the most significant influential values on the accuracy of measurement results was analyzed. The content of quantitative and qualitative indicators of corrections, which must be taken into account during calibration to achieve the highest accuracy of measurements, is revealed. The practical results of studies of measurement instability are given. The analyzer calibration method described in the article can be used in calibration laboratories that have the appropriate equipment and standards.

[1] Recommendation ITU-T G.811 (1997), Timing characteristics of primary reference clocks [Electronic resource]. - Available at: https://www.itu.int/rec/T-RECG.811-199709-I/en.
[2] Recommendation ITU-T G.811.1 (2017), Timing characteristics of enhanced primary reference clocks [Electronic resource]. - Available at: https://www.itu.int/rec/TREC-G.811.1-201708-I/en.
[3] Recommendation ITU-T G.812 (2004), Timing requirements of slave clocks suitable for use as node clocks in synchronization networks [Electronic resource]. - Available at: https://www.itu.int/rec/T-RECG.812-200406-I/en.
[4] EN ISO/IEC 17025:2017 General requirements for the competence of testing and calibration laboratories. [Electronic resource]. - Available at: https://www.iso.org/ standard/66912.html
[5] EA-04/02. Evaluation of the Uncertainty of Measurement in Calibration. [Electronic resource]. - Available at: https://www.accredia.it/en/documento/ea-4-02-rev-03- evaluation-of-the-uncertainty-of-measurement-in-calibration/
[6] M3003 The Expression of Uncertainty and Confidence in Measurement. Edition 4 October 2019. [Electronic resource]. - Available at: https://www.ukas.com/wp-content/ uploads/schedule_uploads/759162/M3003-The-Expressionof-Uncertainty-and-Confidence-in-Measurement.pdf
[7] Z. Zhang, X. Liao. "A Microwave Power Sensor". In: Huang QA. (eds) Micro Electro Mechanical Systems. Micro/Nano Technologies. Springer, Singapore, 2018. doi: 10.1007/978-981-10-5945-2_32.
https://doi.org/10.1007/978-981-10-5945-2_32
[8] X. Cui, Y. S. Meng, Y. Shan and Y. Li. "Microwave Power Measurements: Standards and Transfer Techniques". New Trends and Developments in Metrology, Luigi Cocco (Ed.), IntechOpen, 2016, pp. 3-20. doi: 10.5772/60442.
https://doi.org/10.5772/60442
[9] Y. Shan and X. Cui. "RF and Microwave Power Sensor Calibration by Direct Comparison Transfer". Modern Metrology Concerns, Luigi Cocco (Ed.). IntechOpen, 2012, pp. 175-200. doi: 10.5772/34553.
https://doi.org/10.5772/34553
[10] Y. S. Meng, Y. Shan. "Measurement and Calibration of A High-Sensitivity Microwave Power Sensor with An Attenuator". Radioengineering, vol. 23, no. 4, 2014, pp. 1055-1060. https://www.radioeng.cz/fulltexts/2014/14_04_1055_1060.pdf.
[11] M. Rodriguez, M. Celep, M. Hudlicka, et. al. "Calibration of power sensors for low-power measurement: Best practice guide". EMPIR 15RPT01, RFMicrowave, 2019, 18 p. http://www.rfmw.cmi.cz/documents/deliverables/Calibration _power_sensors_low-power_measurement.pdf.
[12] O. Velychko, T. Gordiyenko. "Metrological Traceability at Different Measurement Levels". Standards, Methods and Solutions of Metrology, Published by IntechOpen, London, United Kingdom, 2019; Chapter 1, pp. 1-21. doi: 10.5772/intechopen.84853.
https://doi.org/10.5772/intechopen.84853