Meet a claim is quite difficult in real production, even in specialized drilling manufacturers. Therefore, the development of reliable criteria for approaches to improving the technology of tricone drill bits is an urgent problem. This is great practical importance for domestic enterprise. The task is set to create rock-destroying insert in the basis of the developed construction. This allows you to increase the reliability of the connection between the cutter insert and the body of the cone. Favourable conditions should be provided for the rational distribution of contact stresses in conjugate surfaces "carbide cutter insert – bush – body of cone". Crucial part here is required rigidity of the carbide cutter insert. Advanced requirements are placed on them regardless of the design and dimension-type of tricone drill bits. They must have higher requirements such as: high reliability, durability of responsible elements of support and rock-destroying equipment, productivity, ability is stand destructive forces and torque are brought through a bit for influence on a face This increases the reliability of its connection with the body of the drill bit. Requirements apply to the design to provide favorable conditions for the rational distribution of contact stresses in conjugate surfaces "carbide cutter – bush – body of the bit cone". The obtained results of stress state modeling indicate that, as expected, with the same forces acting on the insert cutter from 42 kN to 57 kN, the most intense place on the cone will be the "collar" near the cutter. The intensity of stress will be up to 1050 MPa in this place for cones with serial rock-destroying equipment. At the same time, the intensity of stress will be up to 900 MPa for cones with developed destructive equipment, this is 14 % less.
[1] Slipchuk, A., Yakim, R.: The Influence of Technological Factors During Pressing Tungsten Carbide Insert Cutter in the Cone of the Roller Cone Bits for the Reliability Connection. New Solutions in Modern Technologies, 2020, vol. 3(5), 1–143, https://doi.org/10.20998/2413-4295.2020.01.01
[2] Pyalchenkov, V., Kulyabin G., Dolgushin V.: Analytical and Experimental Study of the Deformation of Roller Cone Bit Parts. International Journal of Mechanical Engineering and Technology 10 (3), 204–213 (2019).
[3] Pandey, P., Mukhopadhyay, K., Chattopadhyaya S.: Reliability Analysis and Failure Rate Evaluation for Critical Subsystems of the Dragline. Journal of the Brazilian Society of Mechanical Sciences and Engineering, vol. 40 (2), 1–11 (2018), https://doi.org/10.1007/s40430-018-1016-9
[4] A.s. 1439192. SSSR, MKI Ye21 V 10/16 // Ye21 V 10/52. Burovoy instrument / N. M. Panin, L. N. Dumkin, L. V. Ardasov, V. S. Lavrenov, V. N. Mityushin (SSSR). – №4210632/22-03; Zayavleno 12.03.87; Opubl. 23.11.88, Byul. № 43. – 3 s.
[5] A.S. 909100. SSSR, MKI Ye21 V 10/16. Porodorazrushayushchiy organ / G. V. Lindo, S. I. Odynets, P. A. Podkopayev, V. A. Sarkisyan, V. P. Arestov. (SSSR). – №2967714/22-03; Zayavleno 31.07.80; Opubl. 28.02.82, Byul. № 8.– 6 s.
[6] A.s. 1303696. SSSR, MKY E21 V 10/46. Porodorazrushayushchaya vstavka / S. E. Alekseev, A. P. Hede (SSSR). – № 3872267/22-03; Zayavleno 25.03.85; Opubl. 15.04.87, Byul. № 14. – 3 s.
[7] Pat. 38856 Ukrayina, MPK E21V 10/46. Porodoruynivna vstavka / Yu. D. Petryna, R. S. Yakym, T. B. Pasynovych (Ukrayina).; zayavnyk i patentovlasnyk Ivano-Frankivsʹkyy natsionalʹnyy tekhnichnyy universytet nafty i hazu. – № u 2008 09040; zayavl. 10.10.08; opubl. 26.01.2009, Byul. № 2. – 4 s.
[8] Arzhang Nabilou “Effect of Parameters of Selection and Replacement Drilling Bits Based on Geo-Mechanical Factors: (Case Study: Gas and Oil Reservoir in the Southwest of Iran)”. American Journal of Engineering and Applied Sciences. Vol. 9, pp. 380–385. May 2016, https://doi.org/10.3844/ajeassp.2016.380.395
[9] Satya Prakash, Mukhopadhyay, A.: Reliability Analysis of Tricone Roller Bits with Tungsten Carbide Insert in Blasthole Drilling. International Journal of Mining, Reclamation and Environment 34(2), 101–118. (2020) https://doi.org/10.1080/17480930.2018.1530055
[10] Slipchuk A., Jakym R.: Assessment of Reliability and Criteria for Improving the Quality of Rock Cutting Equipment of Tricone Drilling Bits for Well-Boring Especially Hard Rock. Bulletin of NTU “KhPI” 45 (1321), 77–86 (2018).