EFFECT OF PREHEATING ON CUTTING FORCE AND MACHINING PERFORMANCE OF TITANIUM ALLOY TI-6AL-4V

Authors:
1
Department of Robotics and Integrated Mechanical Engineering Technologies, Lviv Polytechnic National University

The present paper examines the impact of preheating a titanium alloy on cutting force and surface quality during turning. The primary objective of the present study is to ascertain how variations in workpiece temperature prior to machining affect the technological parameters of the cutting process, specifically cutting force and the surface roughness parameter Ra. The experimental portion of the study involved the turning of a Ti-6Al-4V titanium alloy workpiece at numerous preheating temperatures, including room temperature, 300°C, 400°C, 500°C, and 600°C. Prior to the machining process, a preliminary step of preheating was conducted. The experimental procedure was executed employing the following set of cutting parameters: a feed rate of 0.1 mm/rev, a depth of cut of 0.5 mm, and a cutting speed of 150 m/min. The findings demonstrated a distinct pattern of decreasing cutting force with increasing workpiece size. The material's mechanical resistance decreased throughout the cutting process, as evidenced by the most notable force reduction at 600°C. In addition, an increase in surface roughness was observed, suggesting that this process may be conducive to the formation of chips and the establishment of a more pliant interface between the tool and the material. The findings corroborate the hypothesis that preheating can enhance surface quality and reduce tool load during machining of titanium alloys. It is noteworthy that this strategy does not necessitate substantial modifications to the existing machinery. Consequently, it has the potential to be advantageous in manufacturing settings where decreasing tool wear and enhancing productivity are imperative.

[1] H. A. Kishawy, end A. Hosseini, "Machining Difficult-to-Cut Materials", Cham: Springer International Publishing, 2019.
https://doi.org/10.1007/978-3-319-95966-5
[2] H. Zheng and K. Liu, "Machinability of Engineering Materials", in: A. Nee (eds), Handbook of Manufacturing Engineering and Technology, Springer, London, 2013.
https://doi.org/10.1007/978-1-4471-4976-7_2-1
[3] M. F. Ashby and D. R. H. Jones, "Engineering Materials 1: An Introduction to Properties, Applications and Design", 4th ed. Oxford, UK: Butterworth-Heinemann, 2012. https://doi.org/10.1016/b978-0-08-096665-6.00001-5
https://doi.org/10.1016/B978-0-08-096665-6.00001-5
[4] W. D. Callister, D. G. Rethwisch, "Materials Science and Engineering: An Introduction", 9th ed. Hoboken, NJ: Wiley, 2014.
[5] D. R. Askeland, W. J. Wright, "The Science and Engineering of Materials", 7th ed. Boston, MA: Cengage Learning, 2015.
[6] P. Haasen, "Physical Metallurgy", 3rd ed. Cambridge: Cambridge University Press, 1996.
https://doi.org/10.1017/CBO9781107295551
[7] B. Maher, V. Wagner, G. Dessein, J Sallabery, and D. Lallement, "An Experimental Investigation of Hot Machining with Induction to Improve Ti-5553 Machinability", Applied Mechanics and Materials, vol. 62, pp. 67-76, 2011. DOI: 10.4028/www.scientific.net/AMM.62.67
https://doi.org/10.4028/www.scientific.net/AMM.62.67
[8] A. K. Parida, and K. P. Maity, "An experimental investigation to optimize multi-response characteristics of Ni-hard material using hot machining", Advanced Engineering Forum, pp. 16-23, 2016.
https://doi.org/10.4028/www.scientific.net/AEF.16.16
[9] R. Muhammad, Naseer Ahmed, Himayat Ullah, Anish Roy, Vadim V. Silberschmidt, "Hybrid machining process: experimental and numerical analysis of hot ultrasonically assisted turning", The International Journal of Advanced Manufacturing Technology, vol. 97, no. 5-8. pp. 2173-2192, 2018. URL: https://doi.org/10.1007/s00170-018-2087-6
https://doi.org/10.1007/s00170-018-2087-6
[10] S. Pasternak, V. Stupnytskyy, "Analysis and development of a cutting force measurement system under pre-heating conditions of the workpiece", Ukrainian Journal of Mechanical Engineering and Materials Science, 2024. vol. 10, no. 4, pp. 70-78, 2025. URL: https://doi.org/10.23939/ujmems2024.04.070
https://doi.org/10.23939/ujmems2024.04.070
[11] V. Stupnytskyy, S. Xianning, "Research and simulation of the machining process of difficult-to-cut materials", Ukrainian Journal of Mechanical Engineering and Materials Science, vol. 6, no. 3-4, pp. 41-50, 2020. URL: https://doi.org/10.23939/ujmems2020.03-04.041
https://doi.org/10.23939/ujmems2020.03-04.041
[12] A. Slipchuk, "Determination of geometric parameters of undeformed chips at the stage of cut in during multi-pass cutting of the internal gear by power skiving", Ukrainian Journal of Mechanical Engineering and Materials Science, vol. 10, no. 3, pp. 10-18, 2024. URL: https://doi.org/10.23939/ujmems2024.03.010
https://doi.org/10.23939/ujmems2024.03.010
[13] K. Wegener, F. Kuster, S. Weikert, L. Weiss, and J. Stirnimann, "Success Story Cutting", Procedia CIRP, vol. 46, pp. 512-524, 2016.
https://doi.org/10.1016/j.procir.2016.04.110
[14] S. Liao and J. Duffy, "Adiabatic shear bands in a TI-6Al-4V titanium alloy", Journal of the Mechanics and Physics of Solids, vol. 46, iss. 11, pp. 2201-2231, 1998.
https://doi.org/10.1016/S0022-5096(98)00044-1
[15] W. F. Sales, J. Schoop, L. R. R. da Silva, Á. R. Machado and I.S. Jawahir, "A review of surface integrity in machining of hardened steels", Journal of Manufacturing Processes, vol. 58, pp. 136-162, 2020.
https://doi.org/10.1016/j.jmapro.2020.07.040
[16] G. Madhavulu and A. Basheer, "Hot Machining Process for improved metal removal rates in turning operations", Journal of Materials Processing Technology, vol. 44, no. 3-4, pp. 199-206, 1994.
https://doi.org/10.1016/0924-0136(94)90432-4
[17] S. Goel, W. Bin, X. Luo, A.Agrawal, and V. K. Jain, "A Theoretical Assessment of Surface Defect Machining and Hot Machining of Nanocrystalline Silicon Carbide", ASME. J. Manuf. Sci. Eng., vol. 136(2): 021015, 2014.
https://doi.org/10.1115/1.4026297
[18] A. A. Elsadek, A. M. Gaafer, S. S. Mohamed, et al. "Prediction and optimization of cutting temperature on hard-turning of AISI H13 hot work steel", SN Appl. Sci., vol. 2, no. 540, 2020.
https://doi.org/10.1007/s42452-020-2303-5
[19] G. Madhavulu and A. Basheer, "Hot Machining Process for improved metal removal rates in turning operations", Journal of Materials Processing Technology, vol. 44, no. 3-4, pp. 199-206, 1994.
https://doi.org/10.1016/0924-0136(94)90432-4
[20] R. Muhammad, N. Ahmed, H. Ullah, A. Roy, end V. V. Silberschmidt "Hybrid machining process: experimental and numerical analysis of hot ultrasonically assisted turning", The International Journal of Advanced Manufacturing Technology, vol. 97, pp. 2173-2192, 2018. http://dx.doi.org/10.1007/s00170-018-2087-6
https://doi.org/10.1007/s00170-018-2087-6
[21] K. Venkatesan, K. Manivannan, S. Devendiran, A.T. Mathew, N.M. Ghazaly, Aadhavan, S. M. Neha Benny, "Study of forces, surface finish and chip morphology on machining of inconel 825", Procedia Manufacturing, vol. 30, pp. 611-618, 2019.
https://doi.org/10.1016/j.promfg.2019.02.086