1. UJMEMS
  2. All Volumes and Issues
  3. Vol. 10, No. 3, 2024
  4. A REVIEW AND ANALYSIS OF THE INFLUENCE OF TECHNOLOGICAL PARAMETERS ON THE EFFICIENCY OF PROCESSING HARD-TO-MACHINE MATERIALS

A REVIEW AND ANALYSIS OF THE INFLUENCE OF TECHNOLOGICAL PARAMETERS ON THE EFFICIENCY OF PROCESSING HARD-TO-MACHINE MATERIALS

UJMEMS.
2024;
Volume 10, Number 3
: 65-78
Received: August 22, 2024
Revised: September 03, 2024
Accepted: September 09, 2024
Authors:
  1. Oleh Prodanchuk
  2. Nataliya Stupnytska
  3. Taras Olenuk
1
Lviv Polytechnic National University
2
Lviv Polytechnic National University
3
Department of Robotics and Integrated Mechanical Engineering Technologies, Lviv Polytechnic National University

The article analyzes modern technologies for machining workpieces of hard-to-machine materials with a hardness parameter higher than 45 HRC (Rockwell hardness). It is shown that the mechanics and thermodynamics of the forming process in such materials are subject to specific laws of cutting theory, which have systemic differences from the processing of traditional engineering materials. The advantages and disadvantages of machining chromium-nickel alloys using CNB inserts instead of grinding are analyzed. The influence of the cutting tool geometry during the machining of hard-to-machine materials is shown.

cutting process
hard-to-machine material
tool geometry
chrome-nickel alloy
cutting force
shear zones
residual stress
surface roughness.
  1. H. A. Kishawy and Ali Hosseini, Machining Difficult-to-Cut Materials. Basic Principles and Challenges, Cham: Springer International Publishing AG, 2019.
  2. J. P. Davim et al. Machining of Hard Materials, London: Springer-Verlag, 2011
  3. W. König, R. Komanduri, H. K. Tönshoff and G. Ackershott, “Machining of Hard Materials”, CIRP Annals, vol. 33, no. 2, pp. 417–427, 1984.
  4. V. Stupnytskyy and She Xianning, "Research and simulation of the machining process of difficult-to-cut materials", Ukrainian Journal of Mechanical Engineering and Materials Science, vol. 6, no. 3-4, pp. 41-50, 2020.
  5. F. Bleicher, D. Finkeldei, A. Siller, “Machining of Difficult-To-Cut Materials”, in Proc. of the 27 DAAAM International Symposium, Vienna, Austria, 2016, pp. 0473–0479.
  6. V. Stupnytskyy and She Xianning, “Comparative Analysis of Simulation Results of Hard-to-Cut Materials Machining by Coated Cutting Tools”, Journal of Mechanical Engineering – Strojnícky časopis, vol. 70, no. 2, pp. 153–166, 2020.
  7. D. Huddle, “New hard turning tools and techniques offer a cost-effective alternative to grinding”, Tool. Prod. Mag., vol.80, pp. 96–103, 2001
  8. A. A. Elsadek, A. M. Gaafer and S.S. Mohamed, “Optimization of roundness error in hard turning of aisi h13 tool steel”, Journal of the Egyptian society of tribology, vol. 17, no. 1, pp. 53 – 61, 2020
  9. M. S. Mamlouk, J. P. Zaniewski, Materials for civil and construction engineers. Limited: Pearson Education; 2013.
  10. R. Suresh, S. Basavarajappa, V.N. Gaitonde, G. Samuel and J.P. Davim, “State-of-the-art research in machinability of hardened steels”, Proc Inst Mech Eng Part B J Eng Manuf., vol. 227, no. 2, pp. 191–209, 2013.
  11. G. Krauss, “Deformation and fracture in martensitic carbon steels tempered at low temperatures”, Metall Mater. Trans., vol. 32, no. 4, pp. 61–77, 2001.
  12. S.F. Diltemiz and S. Zhang, Superalloys for super jobs. Aerospace materials handbook, Boca Raton: CRC Press, 2012.
  13. T.M. Pollock and S. Tin, “Nickel-based superalloys for advanced turbine engines: chemistry, microstructure and properties”, J. Propul. Power., vol. 22, no. 2, pp.361–374, 2006
  14. E. Akca and A. Gürsel, “A review on superalloys and In718 nickel-based inconel superalloy”, Periodicals of Engineering and Natural Sciences (PEN), vol. 3, no. 1, 2015.
  15. B. Moniz, Metallurgy, NY: American Technical Publishers, 1994
  16. R. C Reed, The Superalloys: Fundamentals and Applications, Cambridge: Cambridge University Press, 2008.
  17. E. Ezugwu, “Key improvements in the machining of difficult-to-cut aerospace superalloys”, Int. J. Mach. Tools Manuf., vol. 45, no. 12, pp. 1353–1367, 2005.
  18. https://www.sandvik.coromant.com/en-gb/tools
  19. I. Baránek, Trends in cutting materials and tools for hard machining. In: Applied mechanics and materials. Trans Tech Publications, 2014.
  20. https://www.sandvik.coromant.com/en-us/tools/inserts-grades/turning-inserts-grades/turning-inserts-grades-hardened-steel.
  21. Yu.V. Petrakov, S.V. Sokhan, V.K. Frolov, V.M. Korenkov Tekhnolohii vyhotovlennia detalei skladnoi formy (Technologies for manufacturing parts of complex shapes), Kyiv: National Technical University of Ukraine “Igor Sikorsky Kyiv Polytechnic Institute”, 2020 [in Ukrainian].
  22. V. Stupnytskyy, E. Dragašius., S. Baskutis and She Xianning, “Modeling and simulation of machined surface layer microgeometry parameters”, Ukrainian Journal of Mechanical Engineering and Materials Science, vol. 8, no. 1, pp. 1-11, 2022.
  23. E.O. Ezugwu, Z.M. Wang and A.R. Machado, “The machinability of nickel-based alloys: a review”, Journal of Materials Processing Technology, vol. 86, no 1–3, pp. 1-16, 1999
  24. M.A. Elbestawi, A.K. Srivastava, T.I. El-Wardany, “A model for chip formation during machining of hardened steel”, CIRP Ann. Manu.f Technol., vol. 45, no. 1, pp. 71–76, 1996
  25. Y. Matsumoto, M. Barash, C. Liu, “Cutting mechanism during machining of hardened steel”, Mater. Sci. Technol., vol.4, pp. 299–305, 1987.
  26. E. Smart and E. Trent, “Temperature distribution in tools used for cutting iron, titanium and nickel”, Int. J. Prod. Res., vol. 13, no. 3, pp.265–290, 1975.
  27. T. Hodgson, P.H.H. Trendler and G.F. Michelletti, “Turning hardened tool steels with cubic boron nitride inserts”, Ann. CIRP, vol. 30(1), pp. 63–66, 1981.
  28. W. Koenig, R. Komanduri, H.K. Toenshoff and G. Ackeshott, “Machining of hard metals”, Ann. CIRP, vol. 33(2), pp. 417–427, 1984/
  29. W. Koenig and M. Klinger, “Machining hard materials with geometrically defined cutting edges–field of applications and limitations”, Ann. CIRP, vol. 39(1), pp. 61–64, 1990.
  30. W. König, et al., “Turning versus grinding: a comparison of surface integrity aspects and attainable accuracies”, CIRP Annals, vol. 42, pp. 39-43, 1993.
  31. F. Klocke, G. Eisenblätter, “Dry cutting”, CIRP Annals, vol 46, pp. 519–526, 1997.
  32. H.K.Tönshoff, et al., “Cutting of hardened steel”, CIRP Annals, vol. 49, no. 2, pp. 547–566, 2000
  33. M.C. Shaw, and A. Vyas, “Chip formation in the machining of hardened steel”, CIRP Annals - Manufacturing Technology, vol. 42, no. 1, pp. 29–33, 1993.
  34. M.A. Davies, et al. “On Chip Morphology, Tool Wear and Cutting Mechanics in Finish Hard Turning”, CIRP Annals, vol. 45, no. 1, pp. 77–82, 1996.
  35. M.A. Elbestawi, et al., “A Model for Chip Formation during Machining of Hardened Steel.” CIRP Annals, vol. 45, no. 1, pp. 71–76, 1996
  36. V.P. Astakhov, S.V. Shvets, M.O.M. Osman, “Chip structure classification based on mechanics of its formation”, Journal of Materials Processing Technology, vol. 71, pp. 247–257, 1997
  37. G. Poulachen, and A. L. Moisan, “Hard Turning: Chip Formation Mechanisms and Metallurgical Aspects”, Journal of Manufacturing Science and Engineering, vol. 122(3), pp. 406, 2000.
  38. T. Ueda, M. Al Huda, K. Yamada, K. Nakayama, and H. Kudo, “Temperature Measurement of CBN Tool in Turning of High Hardness Steel”, CIRP Annals - Manufacturing Technology, vol. 48(1), pp. 63–66, 1999.
  39. Y.K. Chou and C.J. Evans, “Tool wear mechanism in continuous cutting of hardened tool steels”, Wear, vol. 212, pp.59–65, 1997.
  40. J. Barry and G. Byrne, “Cutting tool wear in the machining of hardened steels. Part II: CBN cutting tool wear.”, Wear, vol. 247, pp. 152–160, 2001.
  41. Y. Matsumoto, F. Hashimoto and G. Lahoti, “Surface integrity generated by precision hard turning”, CIRP Annals , vol.48(1), pp. 59–62, 1999.
  42. J.D. Thiele, S.N. Melkote, “Effect of cutting edge geometry and workpiece hardness on surface generation in the finish hard turning of AISI 52100 steel”, Journal of Materials Processing Technology, vol. 94, pp. 216–226, 1999.
  43. I. Brown and J. Schoop, “The effect of cutting edge geometry, nose radius and feed on surface integrity in finish turning of Ti-6Al4V”, Procedia CIRP, vol. 87, pp. 142–147, 2020.
  44. T. Özel, “Modeling of hard part machining: effect of insert edge geometry in CBN tools”, J. Mater. Process. Technol., vol. 141, pp. 284–293, 2003.
  45. Y.B. Guo, C.R. Liu, “Mechanical properties of hardened AISI 52100 steel in hard machining processes”, ASME J. Manuf. Sci. Eng., vol. 124, pp. 1–9, 2002.
  46. T. Ozel, Tsu-Kong Hsu, E. Zeren, “Effects of cutting edge geometry, workpiece hardness, feed rate and cutting speed on surface roughness and forces in finish turning of hardened AISI H13 steel”, Int. J. Adv. Manuf. Technol., vol. 25, pp. 262–269, 2005.
  47. W. G. Lee, J. W. Lee, M. S. Hong, S.-H. Nam, Y. Jeon, and M. G. Lee, “Failure Diagnosis System for a Ball-Screw by Using Vibration Signals”, Shock and Vibration, vol. 2015, pp. 1–9, 2015.
  48. V.Stupnytskyy, et al., “Modeling and simulation of machined surface layer microgeometry parameters”, Ukrainian Journal of Mechanical Engineering and Materials Science, vol.8, no.1, pp. 1-11, 2022.
  49. Y.K. Chou, C.J. Evans, “White layers and thermal modeling of hard turned surfaces”, Int. J. Mach. Tools Manuf., vol. 39(12), pp. 1863–1881, 1999.
  50. V. Stupnytskyy, Ya. Novitskyi, Yu. Novitskyi, S. Xianning, “Comprehensive system for simulation of vibration processes during the titanium alloys machining”, Archive of Mechanical Engineering, vol. 70, no. 1, pp. 85–105, 2023.
  51. A. Tareq and Abu Shreehah, “Extending the technological capability of turning operation”, International Journal of Engineering, Science and Technology, vol. 2, no. 1, pp. 192-201, 2009.
  52. M. Sortino, G. Totis, and F. Prosperi, “Modeling the dynamic properties of conventional and high-damping boring bars”, Mechanical Systems and Signal Processing, vol. 34, pp. 340–352, 2013.
  53. T. Zhao, J.M. Zhou, V. Bushlya, et al., “Effect of cutting edge radius on surface roughness and tool wear in hard turning of AISI 52100 steel”, Int. J. Adv. Manuf. Technol., vol. 91, pp. 3611–3618, 2017.
  54. K. Nakayama, M. Arai, T. Kanda, “Machining characteristics of hard materials”, CIRP Ann. Manuf. Technol., vol. 37(1), pp. 89–92, 1988.
  55. H.K. Toenshoff, C. Arendt, R. Ben Amor, “Cutting hardened steel”, Ann. CIRP, vol. 49(2), pp. 1–19, 2000.
  56. M.Wang, T. Ken, S. Du, and L. Xi, “Tool Wear Monitoring of Wiper Inserts in Multi-Insert Face Milling Using Three-Dimensional Surface Form Indicators”, ASME. J. Manuf. Sci. Eng., vol. 137(3): 031006.
  57. A. Manokhin, Y. Melniychuk, S. Klimenko, et al., “Exerimental estimation of hard turning contact characteristics”, Bulletin of the National technical university Kharkiv Polytechnic Institute, Series Techniques in a machine industry, pp. 16-21, 2023.
  58. P.M. Duc, L.H. Giang, M.D. Dai, D.T. Sy, “An experimental study on the effect of tool geometry on tool wear and surface roughness in hard turning”, Advances in Mechanical Engineering, vol. 12(9), 2020.