INVESTIGATION OF THE STRESS–STRAIN STATE OF THE PLANET GEAR SHAFT AND CARRIER OF THE PLANETARY GEARBOX OF AN ELBOW ORTHOSIS

Received: August 22, 2025
Revised: September 28, 2025
Accepted: September 30, 2025
1
National Technical University of Ukraine "Ihor Sikorsky Kyiv Polytechnic Institute"
2
Freiberg University of Mining and Technology

Mechanical transmissions are widely used in various types of structures and mechanisms in different branches of the machine-building industry. One such branch is medicine. Devices with mechanical components are also used for patient rehabilitation in the postoperative period. Such mechanisms are known as orthoses. Structures of this type must meet several strict requirements—for example, compactness, light weight, safety, reliability, and others. Orthoses must reproduce the lost functions of a healthy person as accurately as possible. As previous work has shown, planetary gears meet the requirement for compactness. Planetary gears provide the necessary technical characteristics. This article presents the simulation and analysis of the stress-strain state of the components of a planetary gearbox for an elbow orthosis. KISSsoft and Ansys software packages were used for the design and 3D modeling of components, as well as for determining the stress-strain state. During the design process, KISSsoft software displays the profiles of the gear teeth and the contact line, allowing further adjustments to be made if necessary. When modeling the gears, the connecting elements were made of 45 steel. The article presents the basic formulas used for the analytical calculation and shows the stress and displacement fields obtained using the Ansys software product.

[1] S. M. Ghoneam, et al., “Dynamic analysis of rotor system with active magnetic bearings using finite element method”, International Journal of Engineering Applied Sciences and Technology, Vol. 7, Issue 1, ISSN No. 2455-2143, pp. 09-16, 2022.

[2] Iaroslav Lavrenko, Maksym Sushchenko, Oleksii Ishchenko, “Frequency response and strength analysis of the elbow orthosis planetary gearbox shaft using FEA”, Ukrainian Journal of Mechanical Engineering and Materials Science, Vol.9, No.4, 2023, pp.27-41.

[3] N. Lenin Rakesh, et al., “Stress analysis of a shaft using Ansys”, Middle-east Journal of Scientific Research, 12 (12), ISSN 1990-9233, pp. 1726-1728, 2012.

[4] B. Gaikwad Rushikesh, and V. Gaur Abhay, “Static and dynamic analysis of shaft (EN24) of foot mounting motor using FEA”, International Journal of Innovations in Engineering Research and Technology, Vol. 5, Issue 6, ISSN: 2394-3696, pp. 57-70, 2018.

[5] Iaroslav Lavrenko, Maksym Sushchenko, Olena Chaikovska, “Simulation of the Gears stress-strain state of Elbow Orthosis Planetary Gearbox”, Ukrainian Journal of Mechanical Engineering and Materials Science, Vol.10, No.2, 2024, pp. 33-45.

[6] P. Krishna Teja, et al., “Finite element analysis of propeller shaft for automotive and naval application”, International Research Journal of automotive Technology, Vol. 1, Issue 1, ISSN 2581-5865, pp. 8-12, 2018.

[7] A. Asonja, et al., “Analysis of the static behavior of the shaft based on finite method under effect of different variants of load”, Applied Engineering Letters, Vol. 1, No. 1, pp. 8-15, ISSN: 2466-4847, 2016.

[8] Iaroslav Lavrenko, Daniil Okladnikov, “Design and strength analysis of the planetary gearbox shafts for an elbow orthosis using Kisssoft”, Ukrainian Journal of Mechanical Engineering and Materials Science, Vol.11, No.1, 2024, pp. 37-43.

[9] J. Joshi, et al., “Design analysis of shafts using simulation softwares”, International Journal of Scientific and Engineering Research, Vol. 5, Issue 8, ISSN 2229-5518, pp. 751-761, 2014.

[10] M. J. Jweeg, et al., “Dynamic analysis of a rotating stepped shaft with and without defects”, IOP Conf. Series: Materials Science and Engineering, 3rd International Conference on Engineering Sciences, Kerbala, Iraq, 2020, Vol. 671.

[11] S. Culafic, and D. Bajic, “Analytical and numerical analysis of shafts' stress and strain states of the hydro-power unit”, International Scientific Journal “Machines. Technologies. Materials”, Vol. XV, Issue 8, pp. 294-298, 2021.

[12] C. Gong, et al., "High-strength rotor design for ultra-high speed switched reluctance machines," in IEEE Transactions on Industry Applications, 2020, Volume: 56, Issue: 2, pp. 1432 – 1442.

[13] M. E. Gerlach, et al., “Mechanical stress and deformation in the rotors of a high-speed PMSM and IM”, Elektrotechnik und Informationstechnik, Vol. 138, Issue 2, pp. 96–109, 2021.

[14] N.F.Timerbaev, et al., “Software systems applications for shaft strength analysis in mechanical engineering”, Procedia Engineering, Vol. 206, pp. 1376–1381, 2017.

[15] N. Rasovic, et al., “Design and analysis of steel reel shaft by using FEA”, Tehnicki vjesnik, Vol. 26, Issue 2, pp. 527-532, 2019.