оптимізація

Аналіз допусків та оптимізація лінійних параметричних кіл на основі частотного символьного методу

У роботі представлено процедури аналізу допусків та оптимізації лінійних параметричних кіл, які основані на частотному символьному методі та реалізовані системою функцій MAOPCs у середовищі MATLAB. Особливість аналізу допусків та оптимізації полягає у тому, що попередньо проводиться оцінка стійкості (асимптотичної) досліджуваного лінійного параметричного кола в заданих межах зміни параметрів та визначення областей допустимої їх зміни, у яких коло є стійким. Виключно у цих областях відбувається аналіз допусків та оптимізація.

Застосування дискретних макромоделей для прогнозування енергоспоживання об'єктів електроенергетичних систем

Запропоновано метод прогнозування добового та річного споживання електроенергії визначених об'єктів з використанням дискретних макромоделей, який дозволяє оцінювати динаміку споживання електричної енергії у майбутньому на основі відомих попередніх даних. Описано процедуру побудови моделі на основі дискретних автономних макромоделей у вигляді "чорної скриньки" для прогнозування енергоспоживання з використанням еволюційного підходу для конкретних об'єктів.

Solving of radioelectronic systems combinatorial optimization problems with ms excel solver

Possibilities of modelling optimization design problems as the extreme combinatorial graph problems and solving them in MS Excel Solver are studied. Drawbacks of existing models from considering their realization in MS Excel Solver are analyzed.

Choosing the optimal location of distribution substations (switchgear) in networks of power supply companies considering external power lines

It has been offered the algorithms determine the optimal location of distribution substations or switchgear for the electrical system , taking into account external power line. Optimality criterion selected discounted costs. It is shown that the optimal position location distribution substation (switching substation) is shifted from the centre of electrical loads in the direction of power.

Process Optimization of Vibroresonance Sewage Disinfection

Для процесів кавітаційного очищення стічних вод від органічних домішок розроблено математичні моделі, що адекватно поєднують їх технологічні параметри із показниками якості обробки. У якості стічних вод розглянуто води пивоваріння, молокопереробної промисловості та воду громадського використання.

Експериментальні дослідження деформативності фрагментів монолітного перекриття з трубчастими вставками і суцільного перекриття

Methods and results of experimental studies deformation of fragments of monolithic reinforced concrete floor are posted: solid brand DF-1; inserts with transverse marks DF-2; mark DF-3 with longitudinal inserts. Overall dimensions of test samples were the same length 2.05 m, width and height section 355x180 mm. Tested prototypes of two concentrated forces, measuring the deformation of the normal sections in the area of pure bending in 3 inclined sections between the supports and lumped forces and deflections general.

Принципові конструктивні вирішення монолітних плоских залізобетонних прогонових будов мостів з полегшувальними вставками

An overview of the existing structural and technological solutions of bridge spans constructions optimization in order to reduce their weight, precast; precast-monolithic and monolithic have been complete.

Impactand particle buffered vibration absorbers optimization and design

Passive, broadband targeted energy transfer refers to the one-way directed transfer of energy from a primary subsystem to a nonlinear attachment; this phenomenon is realized in damped, coupled, essentially nonlinear impact or particle dynamic vibration absorber (DVA). An impact damper is a passive control device which takes the form of a freely moving mass, constrained by stops attached to the structure under control, i.e. the primary structure. The damping results from the exchange of momentum during impacts between the mass and the stops as the structure vibrates.

Application of taguchi method for optimization of continuous drive friction welding process parameters

The objective of present study was to determine optimal conditions to achieve satisfactory friction welds between two dissimilar metals namely copper and carbon steel bars of same diameter. Three process parameters namely speed of rotation, axial pressure, and forge pressure were considered for the present study. Two multiple performance characteristics, considered were breaking load strength and upset. The optimization of the process parameters was done using ANOVA.